VOUNOT Front Door Canopy Outdoor Awning, Rain Shelter for Back Door, Porch, Window, 120 x 80 cm, Grey

This canopy is good value despite being all plastic construction the support frame is very rigid and light. Assembly is easy but here is the only problem I found especially if you don`t have an assistant to help you.I put up the centre support and assembled each of the end ones onto the perspex roof and secured them using the supplied screws in the ends, the plan was then to slide eachg side onto the already mounted centre support and secure in the holes I had already drilled, this was when the problem began. I bent the roofing material into the support but everytime I went to move the outer end it would pop back out again and again before I could secure the first bolt, so I took down the centre support assembled the whole canopy on the ground and drilled in 4 stainless steel self tapping screws (see photos) through the centre support to joint the two half together. After doing this the whole canopy was one piece and fairly strong, but a little bendy. I put the whole thing back up using the centre support first then each end in turn it was very easy once the canopy was in one and wasn`t constantly popping apart. Also the additional two screws I think will give added procetion to the joint in even the strongest of winds.The anchor bolts that come with it are sturdy but I was fixing into a timber structure so opted for coach bolts instead but the supplied fixings look like quality anchor bolts.As for strength well winter is coming and so will the winds I shall have to see how it fairs, that being said I think it will stand a pounding by strong winds - will let you know next summer.All in all for the price a sturdy, well made peice of kit.It is December now and we have had some 70mph plus gale force winds and the canopy has with stood them no problem at all.

I am very impressed with this door canopy as it covers my patio doors and it was relatively easy to assemble too. I paid just under £60 and I believe it is very good value for money.It is very sturdy once installed properly on the wall with provided anchors. I used my Bosch GBH 2 26F SDS drill machine and Bosch Expert SDS 10mm bit and it was easy to drill into bricks. I did have a piece of wooden batten length leftover from my Trellis so I marked the holes on wood while the assembled canopy stayed on ground and then drilled through the wooden batten to create a template. Once all the holes lined up on Batten, it was easy to mark up the exact location of 6 holes needed to mount it on the wall.Used a mallet to drive the anchors in the wall starting from the middle bar of the canopy. I used my Amazon Umi Spanner rachet set to tighten the bolts. After that just put those plastic caps provided to hide the bolts. Job done in an hour not including the hour for assembly. So for two hours of DIY, I have a very stylish and sturdy canopy sheltering my patio doors from rain and snow, what more you want.I would definitely buy more for my windows in few weeks time.

I think it looks really nice up, covers where the wife parks her bike at the back of the house and covers the side door.As said looks good on the wall, its getting it there. Its not hard but definitely something that gets better with practice. A single unit, yeah, doddle. As long as you drill the holes in the right place, depending on your brickwork i would recommend buying some proper m8 rawl bolt fixings as the supplied ones are at best, sufficient.Fitting multiples, the one i put up has 4 sections done solo. You need to pick a centre section with an arm each side and fit that, then work out on each side, clear panel and arm. Offer up the panel and put the outer round end in and work in, then put in the fixings. approx 96mm centres for the holes.A laser line helps a lot too.

The media could not be loaded. Great canopy.easy to fit.i built the single canopy on the ground measured the holes on brackets 37.5 inch apart.and 6 in top to bottom of frame work.may need help to hold canopy up when putting bolts in and tightening the 14mm bolt heads.i drilled holes with a 11mm masonry bit.

Easy to fit together and install, like that the polycarbonate is in one piece and the flutes run downwards so any condensation runs out. Seems strong and secure.

Product looks good, and seems good value. I tried fitting today, a job than should have been around 2 hours has still not been completed. The problem is the fittings supplied. The brackets that bolt to the wall have thick plastic where the top bolt passes through and thinner plastic where the lower bolt passes through. Using the fittings supplied the lower bolts fit OK, but because the plastic is thicker where the top bolts pass through the fitting bolts supplied are too short, so you cannot fit the canopy. I have had to spend £9 at Screwfix for longer fittings, which I will have to cut to fit, and I still have to try and remove the old fixing from the brick wall, so I will have to start again tomorrow or next weekend. Over all, very disappointing. It is a real shame because when I eventually get this fitted, I think t will look good and do the job, although I also think you will need to seal the canopy with some clear silicone against the wall because there is no seal.

The media could not be loaded. Good quality.Would highly recommend better raw plugs and some bolts.Best to use some self tapping screws to strength the frame.

This is 120cm , 200 would not fit this space, 160 would have been perfect. Goes together easily enough, took 2 of us to fit. Supplied bolts are certainly strong but sheath needs to be left at least 2cm out of the wall when fitting otherwise the bolt will not reach the thread of the nut. Instructions are ok for assembly but not for attaching to the wall. I used a 10mm drill bit which worked ok. Perspex canopy was evidently squashed during transit in a couple of places but it doesn't draw the eye when fitted. Overall OK for the price.