HULPremium Aluminium Carrying Case for DJI Phantom 3/4 Drones

No.... the cat is not included... you need to provide your own. That said this is a nice, sturdy case that is pre-formed inside, so you don't have to tear out foam chunks. Everything fits well and is protected from travel hazards. As you can see you can even leave the props on the aircraft. (although for long periods you might want to remove them to prevent possible warping) At under $100.... you cannot go wrong.

Great value for the price, exceeded my expectations. The Phantom 3 Standard slide right in like it was made for the case. The PS3 controller took a little bit to configure but as soon as the device clamps locking nut was loosened the controller fit nicely. There are only two places for the DJI Batteries and the batteries must be installed upside down or they WILL get stuck. I have left the blades installed for more than a month and flown more than 10 hours during that time. The blades are protected and unaffected by being installed on the drone while in the case.Plenty of room for an iPhone 6, Andriod Phone, and an Andriod Mini-Tablet. The power cords must be carefully wrapped in the back right storage hole so the cable ends lay in the Controller storage area. Spare IOS and Android USB Cables and power packs are stored in the front right storage hole with no problems.Would like to see a cutout in the foam on one end for paperwork. A better place to store spare Propellors must share a compartment with other items.

Nice design and storage capacity, easy to transport you drone, the functionality is superb, provides nice protection and so far waterproof.

well made no issues

Fits my HS100 perfectly with props on. Battery slots are a little large but I put the batteries in sideways to keep from slipping, also add some foam to bottom for landing gear to sit on without hanging on props. Included foam cutout pad just has to be pushed to the bottom.)Good price, seems sturdy (not Airline proof though!) Hard to find HS100 cases. at any price.

At first sight, this case looks huge, but its within airline carry on dimensions. I wanted a storage case for my P3P without spending too much money and this seemed to fit the bill. Over all, the case is nice, for the price, but you can see why its priced the way it is. It says aluminum case, but as another review stated, only the frame of it is, the actual side panels are hard plastic. The hinges look a little weak, and only time will tell how they hold up, but since this is for a drone I don't don't always fly, it should be fine. The latches work without binding and they lock/unlock just fine with the keys. Now, let's get to the interior...Let me start by saying, there's plenty of room for all your gear. The P3P fit just fine in it's cutout without a battery installed, and a little snug with one installed. The biggest issue I have are the cutouts for the battery and transmitter! From the looks of things, the battery cutouts were made for the P4, which is why the P3P batteries are loose in them, but with the case closed it stays put. I put one of my P4P batteries in the cutout and it confirmed it was cut for it. Ok, now to my Main issue, the controller cutout! I don't know which controller it was cut for, but it wasn't for the P3 or P4 controllers!! It looks like the cutout is about a 1/4" too narrow. You have to push down some to get the controller to go in, and after you do, the sticks get snagged in the foam a little. After some trial and error, I did find an angle that's a little easier to slide the controller in with some clearance between the sticks and foam. It shouldn't take much to get the controller to fit better with an exacto knife, but come on Hul, how hard is it to adjust your cutter to make cutouts to fit the controller?Anyway, even with the cutout issues, I will keep the case. For the price, its more than adequate to store my P3P in and it does hold everything. However, I would caution anyone who intends to do major traveling with this case. The side panels flex a little but may not take too many knocks. However, it is a lot better than just carrying it in a backpack. Oh, on a side note, it's nice to have the option of keeping the props on the drone if you want to deploy it quickly, but for storage I would take them off.

Buena calidad, presentación y especificaciones. No llegó la llave.

Used for several months now, and I take out my Phantom 4 Pro several times a week for work. The case has held up with no signs of failing. Fits everything I need, the drone fits snug with plenty of padding, and the best part, I don’t have to take off the blades! Excellent case, great value. I recommend this case to everyone that has a Phantom!