Size:1/2 Inch Technical Parameter: Product size: 1/2" FNPT DN15 Maximum Working Pressure: 1.0MPa Circulation Medium: Water,Oil,Gas Rated Voltage: AC/DCDC9-24V Wiring Control Methods:CR01/CR02/CR05 Working Current: 80MA Open/close Time: 3-5 sec. Valve Body Material: Stainless Steel 304 Actuator Material: Engineering Plastics Sealing Material: EPDM Cable Length: 0.5m Environment Temperature:-15~50 Celsius Liquid Temperature: -5~100 Celsius Manual Override: NO Indicator: NO Protection Class: IP65 Application: 1.HVAC 2.Water treatment 3.Chemical process 4.Small industrial equipment for automatic control 5.Replacing solenoid valve, particularly when solenoid cannot work reliably 6.Automatic control systems 7.Efficient water-saving, water equipment 8.Solar hot water project 9.Regular watering the flowers, Timing humidifying，timing of drainage of Air compressor . Features: 1).Smart shape, Perform reliably, large output torque, as long as 50000-100000 times , convenience for all kinds of requirements. 2).Float ball design, no leak, large flow, the valve is bi-directional ball valve , regardless of inlet and outlet , most suitable for heavy dirt and long time no action. 3).The conditions that solenoid valve can not work. 4). High protection class, can be worked in moist conditions. 5).POM cooperate with metal gear, the POM gear is used in high-speed level to reduce noise, At the same time metal gear is applied at the low-grade to ensure the reliability of the gear. 6).Electrical and mechanical limit integrated design, accurate localization , high consistency , put an end to swing of valve.
R**M
Brilliant idea.
The description for the function of this valve seemed a little sketchy when I purchased this valve I decided to take a chance and try it anyway. To be clear, the valve will open when AC or DC voltage is applied. I tested this with a 9 V battery and it opened and stays open so long as the battery is attached. When I installed it In my boiler I connected the valve to a 24 V AC power supply and it also opens as soon as voltage is applied and remains open until voltage is turned off. Thus I confirmed that it works with either AC or DC voltage. Amazing. Nevertheless, the electronics do not seem to overheat even though power remains on. I gather this is because there is a capacitor that is charged up to opens the valve rather than using a coil to keep the valve open. If this is correct, then this is a brilliant design idea. I didn’t tear into the electronics to verify this, so however it works I’m plenty happy with it so far. You can audibly hear the valve mechanism operate when voltage is turned on or turned off which takes a couple of seconds to fully open or close the valve. I can’t hear any hum while the valve is open.
L**.
Super happy with the purchase
I purchased this valve to use in conjunction with an auxiliary diesel tank in my Ford F-250. I have a 60-gallon Titan tank in the bed that works off of gravity feed. The system works well but the manual valve required that I unroll my soft tonneau cover each time I turned the valve on or off. To eliminate the hassle and wear and tear on the cover I installed this valve. It's currently wired into one of the upfitter switches and am loving the set up. When my gas gauge for the factory tank hits a half or quarter I just flip the switch. If I forget to turn the switch off there are no worries as the valve closes when there is no power (such as when the key is off). Super happy with the purchase.
S**O
Very easy to use
I use several motor driven ballvalves a year in various projects. I had been using the 3 wire control method that requires a SPDT switch to reverse the drive voltage. This valve only requires 2 wires and simple on/off SPST type switch. Much easier to interface to my controls (custom microcomputers). A very slick upgrade. BTW, I use these valves instead of a solenoid for three reasons; they never clog, full flow opening and they much less power (less than 10% as much).
M**D
would not close fully at first
After installing and operating on 14.5VDC the unit sounded like it was struggling to open. It would not close more than half when power was removed. I cycled it several times and it started to improve. After about 40 cycles it now fully closes and sounds a bit more healthy. I worry about its longevity though.
T**.
Works perfectly
I used this valve to remotely turn my air supply on/off through a smart plug. (Alexa, turn on the air compressor)I bought the stainless full port 2 wire. That way when the plug/power turns off, the valve closes on it's own. Air compressor is in a separate building, which was a pain to have to go turn the ball valve each time i needed air in the other shop.
C**V
Full bore design
So far seems to work great.For those wondering, there is a difference between this product and the other BacoEng product with the same specs. The Akent version seems to be full bore vs. constricted flow on the BacoEng version. Because of stock issues, I ended up with a bunch of BacoEng versions and only one Akent. Wish it was the other way around.Otherwise they appear to be exactly the same product see photos attached.
C**G
Very good quality
Work exactly as described. I'm using these on a remote water system in the crawl space in our cabin to shut down and drain the pipes. They work awesome.
D**
works great
good quality
Trustpilot
1 month ago
2 months ago
