ELEGOO 1.75mm PLA 3D Printer Filament, Dimensional Accuracy +/- 0.02 mm, Compatible with Most FDM Printer, Black 2KG

Update 10/04/2024: BACK AFTER 1 DAY SHY OF A YEAR! So it turns out the filament wasn't the issue, but was a hot end fan and a power supply fan that were causing the issue. Apparently they were both dying and not cooling the heat sync and/ or power supply adequately. Those were causing intermittant issues with almost all filaments other than one brand that starts with and O.This filament is printing really well currently, and havent had an issue with since doing a major overhaul of my entire hotend assembly and replacing the powersupply fan.5 Stars for Quality of the filament5 Stars for quality of the prints with the filament5 Stars for Elegoo Customer Service (Though they should get 10!)5 Stars for Elegoo all around from me!----------------------------------------------------------------------------------------------------------Update 10/05/23: If I could rate customer service at Elegoo, I would give it 5 stars! Very responsive, and willing to try to get issues taken care of in a timely manner. However, I am settling on a 2 star review of Elegoo's PLA and PLA+. I was sent 2 rolls of their PLA+ to replace the PLA rolls that I purchased, and spent the better part of 2 evenings experiencing the same issues that I originally had with their regular PLA (Under extrusion, clogging, etc.). I even went back and used my filament drier on both of the previously purchased rolls of PLA for 60 hours each, and still am unable to print with them. I love Elegoo, and will always recommend their resin/resin printers, but I can not recommend their filament at this time. I'm going to try to dry out the PLA+ rolls for 80 hours each and see if that makes a difference.Update 09/25/23: Adding 2 stars to my original review. Elegoo customer service was super quick and friendly with a response and reached out to me to offer an option to replace or refund my purchase. I chose to have them replace the rolls, and they stated that they would be sending out their PLA+. Will update review again once I get a chance to test out the new rolls!I bought 2 spools of the black, and printed just fine through half of the first one. Then I started havingissues with adhesion, under extrusion, and clogs in my hot end. I was printing at 205C, and leved the bed between each failed print just to rule those 2 factors out. I even tried to increase the temp, but still had print failure after print failure. So I thought maybe the filament had taken on some moisture. I opened the second roll, and the SAME issues developed.I love most other Elegoo products, but would steer clear of this filament for now.

Worked perfectly for our prints. Flow was perfect. No issues with clogging.

Awesome. I love elegoo filament. The colors are accurate and it doesnt clog or tangle. My printer flows the filament fine and prints it quickly.Current printers: Bambu X1C, Ender 3 V3 KE

This is my first (and last) time using Elegoo's PLA. I'd never had problems printing until I used this. Getting it to stick well to my glass bed has been a constant battle and resulted in more failed prints than any other brand by far. When it sticks to my bed the prints are great, but there's a 50% chance that it will detach at some point or the bottom layer will be a mess.:Revision 5/22:Elegoo contacted me and offered to replace the spools. I agreed and a few days later they arrived. I was unable to test for some time, but today printed 7 parts that take ~1 hour each with zero problems at all.Elegoo's eagerness to make it right and the good performance of the replacement filament makes me want to buy more from them in the future. I'm sure I will.

The color is not as nice and shiny as the rapid pla plus however it is still a nice black. It will not be a repurchase from me as I enjoyed the experience of the rapid more. I did see that this one did not stick to the plate as well so I had a lot more of print tragedies. Overall very good though