PartsBroz WP3392519 3392519 Dryer Thermal Fuse G4AP0500 TF091C - Compatible With Whirlpool Kenmore KitchenAid Roper - Replaces AP6008325 PS11741460 WP3392519VP WED4815EW1 110.60022010 WED4800XQ0

Dryer was completely dead. This was a quick fix that didn't cost much.

My Maytag electric front-load dryer (purchased approx. 2011) stopped working: the control panel lit up, it would accept settings, and the drum light all worked, but when you pressed "start", the dryer would not turn and would not tumble or heat. My vent had clogged and the dryer overheated, melting the original fuse. Confirming the diagnosis required removing the old one and running a multimeter across it. If it shows 0 (or close to zero) ohms of resistance, your part is GOOD, and do not buy this part---you don't need it. If it shows 1 / infinity / no current going across the old part, your part is BAD, and you should consider buying this one (double check that it fits your model first.). This thermal fuse was moderately easy to replace -- a little tight to find unscrew it, but I ignored videos that showed a guy removing the drum -- that was overkill. This thing could be reached just by removing the panel below the door, and it was just below the bottom of the drum -- slightly obscured from view, but with a flashlight I could see it up and to the left. Hard to see, but easy to reach by hand. Whole thing requires only three screws to repair: two screws removed the exterior panel below the door, and one screw held this part into the blower housing. From there, disconnect two wires, and it came right out. (Don't worry about crossing the wires...they can be installed on either of the two posts....not polarized; it will work either way). I will reiterate that it was tight quarters getting up in there, but even with my huge "grand-dad" hands I could get in there and remove it. A quarter-inch socket wrapped with grippy electrical tape allowed me to turn the screw by hand in a place where a wrench would not fit. SAFETY NOTE: When you replace this part, it is **ESSENTIAL** that you clean out the entire air exhaust pathway, from the lint screen all the way to the outdoors vent. Lint will cake-up in the vent and cause this part to fail. That is dangerous. Thankfully, this part is an inexpensive and quick repair, and it protects you from a possible fire. And as a bonus: cleaning out the air exhaust path made the dryer work a lot faster, saving energy and time. And (duh!) always unplug it before you work on it.

My clothes dryer stopped working in the middle of a cycle. People told me to check the electricity. I was told to check the door. I did my research and ordered this fuse. I took the dryer apart, vacuumed everything, borrowed a multimeter (to make sure electricity was not going through the circuit), tested the power and changed the fuse. My dryer now works like a dream...like it never stopped on me. We were in the process of buying another dryer for up to $700 but for less than $7, my tried and true dryer continues to work. I'm very proud of myself. :) Thanks for this fuse.

Not a big deal to install and it works.

My dryer was tumbling but wasn't heating so I googled how to fix it and all I needed was this part. Fast and inexpensive fix!

This thermal fuse was a replacement part for my Whirlpool dryer purchased in 2011. Just look up replacement part numbers. East to install. So far so good.

Part fit and work perfect! Had no issues upon installation. Didn't get picture of the NEW thermal fuse but attached one of the old BLOWN thermal fuse.

It saved me to spend a lot of money to buy a new dryer , I replaced with this part and now my dryer works perfectly!! Thank u!!!

Works and was easy to replace. Don't know what else to say. Arrived quickly.

Buena refacción opera de manera adecuada.

La pièce était parfaite pour ma sécheuse qui fonctionne à nouveau 😃

Funcional

Does what it's supposed to and fast delivery.