Electric Pump Inflation Valve Adapter with torque tabs for FAST iSUP/Kayak/RIB Inflation, Bravo and Halkey Roberts H3 Inflation Valves. Patent Granted 3/18"

Only an idiot would fault the adapter itself (unless it was literally defective) from any issues. I was almost scared off from purchasing because of useless bad reviews lol! I have an Aqua Marina SUP, that needs 15 psi. I used the adapter with an electric pump and It worked perfectly!!!! I have a Bonaire 120 volt inflator, which is not expensive (get from Walmart) and got to magic number of 15 psi 29 min, but beats the hell out of pumping by hand. My electric pump has the gauge built in, so if you turn off a moment get exact psi range you are at and no pressure is lost when checking. It stays sealed while on, even if power off pump for while. It has to do with quality of pump in order to work, the valve stayed on perfectly and did its job. Great product!

I purchased this to replace the Summit 2 air adapter that came with my Wilderness 12 (Colorado style) pontoon raft. Although the this air valve adapter is not advertised as a Summit 2 type valve, it works fine. Well constructed and sturdy, it comes with an extra O ring. This air adapter makes it very easy to use low pressure electric or manual pumps designed to inflated bicycle tires and other low pressure equipment.

I have an air compressor at the bottom of my condo building so I bought this adapter to use on my Naish Glide inflatable paddle board. It comes with multiple rubber washers, but the larger one that comes on it works well for a tight seal on mine. It pumps up my board to 15+ PSI in about 7.5 minutes. I wish I could keep the air pump fixed on the board while filling up (like car pumps) but that's not major.

Wakooda adapter is on the right in first photo and on top in the second photo. The iRocker valves is wider than the Wakooda adapter. The iRocker requires a pin to push down and open the valve on the SUP. The adapter does not have the pin and the diameter is smaller than the iRocker valve and therefore when the adapter is inserted it will leak air unless you apply a lot of force. It will work, but it is not the right product for iRocker.The product appears to be of good quality and should work with the advertised brand SUP's.

Every ISUP owner needs to own this connector. Previous pumps I've used require you to manually hold a non-threaded hose into my paddleboards while inflating, meaning you have to be there holding the hose the entire time to keep it from disconnecting. This things allows you to connect any pump with a Schreader connection and let the board inflate without any babysitting. Just connect, turn the pump on (i.e. set the psi), and then let the pump do it's magic.Pro-tip: If you are using a compressor pump (which you will need to get the board to inflate to inflate above ~5psi), and it isn't 2-phase, you will want to use a normal non-compressor pump, or the manual hand pump that came with your board just to get your board to the point that it takes shape. Compressor pumps are great for inflating things to high PSIs, but they are very slow, and most people that trying to inflate boards from scratch using ONLY a compressor pump will be waiting upwards of 20 minutes. Shave off more than half of that time by simply getting your board to 1psi so it takes shape, which is actually very easy; it's getting it from 3psi up to 15psi (or whatever your board calls for) that is the hardest and most exhausting part, so let the compressor pump do that part. Best of luck!

It does what it says, but it takes forever to get it done. I promise, you will go back to manual pumping. This takes a very, very long time. How long I'm not sure. Never waited long enough to see. Tried it fir 30 mins straight with a dewalt air compressor that powers my tools....I gave up. Please understand I am a lazy, lazy man. EVEN I WENT BACK TO MANUAL! I wanted so badly for this to work but unfortunately it's not to be for me.

Definitely not fast inflation or any inflation at all. Like the other reviews on this product it did not work. It limited the air flow so much that the second I put it on my electric pump it registered 17 PSI. That was with my paddle board fully deflated. Even when it wasn't connected to anything it registered 17 PSI on my electric pump which means this adapter was restricting normal airflow and probably would have taken 3 hours to actually inflate anything even if my pump would allow it. but since I had my compressor pump set to shut off at the recommended 15psi for a paddle board it immediately shut off in the first second as it registered 17psi the second I turned it on.

Make sure you NEVER lose the gaskets that come with this or you’ll be sorry. Otherwise it’s the best ally to pumping your toys with a compressor quickly and efficiently. This works for me for my body glove SUP board and I freaking love it. I’ve been close from losing the rubber o ring gasket and it won’t work without it, it leaks, so not sure if I have mentioned this but, DO NOT LOSE IT

Connected to an air compressor for tires. Takes about 15 Minutes to inflate a 12ft paddleboard to 15PSI.Beats pumping it with the hand pump. Sit back and relax while the board inflates, and have energy reserved to paddle once inflated!

Literally the beat thing to buy if you have a paddle board

It is exactly what I needed to inflate my paddle board with a air compresser

Based on previous reviews, I was nervous buying this. My concern was unfounded; it works exactly as it is supposed to. I was using this on an inflatable boat with Halkey-Roberts New Short valves, and this connector gets a nice seal. The plastic also feels quite solid (much sturdier than the connector I have for my hand pump).Note that this isn't necessarily the best tool for filling an entire boat. Hooked up to a shop compressor, it still took a long time to fill. This is expected, given that you're trying to push a lot of air through a very small opening.

We use this with a compressor to blow up a paddle board. Works awesome.