Not Yet Another Mop Broom Holder, Clips Hold Everything Better Than Rollers, 4 Sliding Grippers and 4 Hooks, Wall Mount on Aluminum Rack by 2 Screws Only, Tools Organizer for Garden, Garage or Closet

I purchased two of these to hold our hockey sticks. I love that I was able to easily remove the little hooks out which gave me plenty more room to play with the position of the stick holders (I stacked 2 of these on top of each other to hold 8 hockey sticks). Holds the heavy sticks better than the mop and broom holder system with the plastic rollers (I ended up using that one in the utility closet) and also looks much better. Easy installation by one person.

Edited: three years in, still works great!So I bought this a in 2018 and we've been using it pretty much every day since then. It's been used by almost everyone in the family and it's held up great. I'm not noticing any loss of grip from the holders. It works much better than other types of tension-based holders that rely on springs. I don't want to oversell it, but with nine kids, it's definitely been put through its paces (and arguably the wringer as well) and it's done its job.

Just what I wanted. Easy one had use and it holds everything securely. Aluminum, plastic and silicone means it will never rust. Just hang up the wet mop to air dry. It was easy to assemble and mount. I ordered 2 extra clamps and installed one on the original bar. A 6th would likely fit but be really tight and make the hooks inaccessible. 5 fit just fine with all the hooks between them. I was installing in an unfinished utility closet, directly to a horizontal 2x4. That is to say it’s really sturdy. Design, fab, and finish were good. Just want I needed for my closet. I will order this again when I find a place in the garage or upstairs for one.

I like this holder. It certainly grips the bigger and heavier push broom with no problem. It came with a couple of anchor bolts for drywall installation. But I had some heavier duty ones that I used instead. I’m sure that the given ones will work. Since I already had the stronger anchor bolts it doesn’t hurt to stronger ones for installation. The screws just fit through the holes for mounting. I like that it uses aluminum for the part touching the wall. Screwed down tightly there is no wiggling what so ever. I guess if someone really wanted to make surer nothing works loose over a period of time. One can drill a third hole for adding a third anchoring point. I will buy another one.

Great product. Absolutely no slipping has occured which was my main concern since it would be right above our washer water hoses. Just nit picking here, but wish the instructions explained a bit more in how to readjust the hook and clip placement. When I received the item everything seemed a bit snug and I didn't want to break anything by pulling to hard.Turns out you pull off one of the end caps, which is actually a hook and then everything starts to loosen up to be moveable.

This is probably the fourth different type/style of mop broom holder I’ve tried over the years. And it’ll be the last! It’s only been up for a week now and I love it! There are actually two here. It took 10 minutes to install them both. Well, probably 30-40 minutes. Including finding the drill, bits, etc and removing the old ones. Definitely well made. Easy to rearrange the grippers and hooks. And it really HOLDS the handles in the grippers. At first I thought the hooks were going to be useless. But they are far from useless.

I've tried three different versions of mop holders: the kind where a roller binds against the mop handle, the kind where a spring-loaded elliptical rubber piece swivels down, and this.This one works far, far better than the first kind and almost as well as the second. I did not have any problem (contrary to some reviews) with putting large-diameter handles (like shovels) into it.One minor quibble: the screws that come with are much too short to reafch a stud through the sheetrock; and I wouldn't count on them holding up several heavy showvels.

I really like this concept of the push in holder thing (command strip makes one but they only come in packs of 1 for like $10 each). I thought this was a much better deal and it’s nice and works. I just wish you could remove some of the hooks or holders. Kind of hard to install w/ them all on there, but not impossible. Plus there is like 2 hooks on each side that are really close together, I would probably take one off of each side if I could to make it more functional.

Only the piece that goes on the wall is aluminum. Everything else plastic. Not sure if the grip part is silicone. That is the main reason I purchased it. I think it is rubber. Can not even hold a hammer. Sending back.