Badger Wheels Adjustable Stainless Steel Axle for Yeti Tundra Coolers (35-160 QTS)

This cooler wheel kit is the best on the market. High quality materials. This the the second Bager wheel kit I own they are absolutely awesome! They make camping, boating so much easier.

I bought the wheels (single axle) separately. This handle completed the modification, Without a handle, the OEM rope handle is just too short and I have to bend over to pull the cooler which is fine for a short distance. This handle makes the long distance runs much easier. Plus the handle makes the cooler level when its in its final spot. I've seen other reviews that claim this is an expensive item, but so is a Yeti cooler. Yes, the item isn't inexpensive, but it's a quality product and sometimes you pay more for quality. This and the wheels were a good buy for my Yeti (and my lower back)!!!

Fit perfectly on my Kenai 45. I installed it on the side with no drain plug, as I had installed some wheels on the other side. So much easier to pull compared to the rope strap! Easy install too…

It does what it says. but I had been expecting at best some hollow roto molded wheels like youd find on a sporting goods or hardware store rollibg cooler. these things are more solid than some go kart wheels Ive used in the past! each wheel is heavy and solid, with a good ball bearing. aside from the slots used for adjusting size, the axle is solid steel. the mounting tabs are 1/8 inches of solid stainless with a good solid weld. Wheel system is built like it expects to run King of the Hammers!

As title states handle sucks. Installed per instructions, I was a little concerned when they sent sticky tape to secure the front of the handle to the cooler but I still installed. I prepared the surface as instructed and still first pull of handle and the aluminum bracket pulled from cooler and bent forward. Very disappointing considering the money spent in this product.Wheels work great on pavement and grass, soft sand they drag a little but still work good. Wheels are a 4 star handle is a 1 star.

As a long time customer of Amazon.I must say this is by far the worse packaging of any product. First of the The wheel frame was warped and I had to knock even with a rubber mallet to fit properly. Secondly, there was no stainless steel screws that came with the handle and last but not least the adhesive appeared to have deteriorate as it was sticking to cooler. The clear tape on it appeared to have been tampered with and might explain the lacking of sticking power. I had to apply small dumbbell weight to keep constant pressure in hopes that it stick. I'll wait the recommended 24 hours before moving with fingers crossed that it works. I usually do not write any comments but this really pissed me off as I spent several hundred dollars for a quality rated product but from an apparently poor quality seller. Extremely disappointed. I will never purchase from this seller again and will spread the word. Please take pride in packaging and inspection of product before sending it to buyer.

Great product, I only wish there was a couple of things different. The tape on the handle brace wasn’t strong enough to stay attached, I had to add screws so I wouldn’t bend. And using the handle as a stand for the front side is a good idea, it would be better if there was a way to secure it so when you bump the cooler it doesn’t slide over itself. Price is a little high but it’s well built and makes hauling my Yeti 75 much easier.

This is a very capable accessory. It seems durable and well built. One potential negative was the installation process. I used it on a Tunda 45 and likely due to excess variations in cooler sizes I found the top attaching bolt “bottomed out”, even with zero extensions, before it was fully seated in the top accessory slot bracket, which would have prevented the lid from closing. An easy workaround was found by loosening the barrel nut on the plunge mechanism, allowing full seating of the top bolt. After re-tightening the barrel nut rather snugly I am confident this setup will likely stay attached on its own. However my suggestion would be to incorporate a larger knurled surface on the barrel nut as doing so would allow much easier R&I or adjustments without needing access to tools.