PEI Sheet Use: Thickness: 0.17mm Compatible with PLA ABS PETG TPU and other most filaments. The Polyetherimide sheet comes with 468MP adhesive already laminated to the PEI. Apply the PEI with slight pressure and at an angle to prevent and minimize air bubbles. Once applied set the print bed to 60C and apply pressure evenly across the PEI in a sweeping fashion to firmly set the adhesive. Please use a towel to avoid getting burned. Level the bed and set the height of the nozzle before printing. About How to install the PEI well on the Steel spring: clean the steel spring with some alcohol; rip off the PEI adhesive, spray some alcohol on the PEI surface, then directly stick on the steel spring surface, rip off the PEI dustproof film When the print is completed, let the bed cool, and the part will be easy to release from the PEI surface. Parts are actually easier to remove if released before the bed becomes completely cold. Magnetic Base: Magnetic base that is adhesive-backed for easy installation PEI Sheet Maintenance: Clean in between prints with isopropyl alcohol and a lint free rag. Acetone can be used instead of isopropyl alcohol, but the bed must be cold if acetone is used. Optionally, light sanding with 600-1000 grit sand paper can be done after lots of printing to give the PEI sheet more life. Package Includes: 1X 300mm Steel Spring 1X 300mm PEI 1X 300mm Magnetic sticker B side
M**.
Can't imagine printing without it
When I got my Creality CR-10S Pro, one of the first things I did was replace the stock buildplate with this one. I can't imagine having to scrape models off the bed. I just wait for the buildplate to cool, lift the sheet, flex it a bit, and my pieces pop right off. I keep the buildplate temperature at 65 during the print and I don't have any issues with losing adhesion. This flex buildplate doesn't cover 100% of the bed on the Creality CR-10S Pro (12" x 12"), but it's close. It's short about 3/32" on each side (so 3/16" total in the x direction) and a total of 3/4" short in the Y direction (front to back). I noticed that the bed heater doesn't reach completely to the edges of the buildplate anyway, so I figure close enough is good enough for me. This model was recommended to me by a friend, and I would recommend it to anyone else looking for a good quality flexible buildplate.
M**.
Bed adhesion on this is HORRIBLE
I got this plate because it's the only one that almost fits my ender 6. It's a couple mm larger than the factory bed, and that's fine. I am 100% happy with the size. I just had to remove the front clips. However, the adhesion is absolutely horrible. I've tried every method of getting the filament to stick to this bed and it's a no go. If the nozzle is too close, it curls up, if it's too far away, or even perfectly leveled, it just kind of slides around. I've tried glue and hairspray and the glue just makes it even more slippery. I've had one successful print out of seven. All the corners curl up and if I run my finger over it or try to push down a corner, the piece just slides around. On the original ender glass plate, It stuck really well. I got the flexible build plate because of how hard it was to remove the pieces from the ender 6 bed. It was so stuck I was actually damaging the more fragile pieces to remove them.
A**.
2 bad packages in a row
My first package was obviously a used return, no problem, I got a replacement...the replacement had the magnet sticky tape side stuck to the bed, also this replacement bed is bare spring steel not pei like my order says. Also multiple delays with both deliveries.Technically I haven't gotten to use this product, it might print excellent for all I know but I highly recommend buying elsewhere if you're wanting to try this product.
J**.
Works as it's supposed to, good adhesion during print and easy to remove parts
I have been using this buildplate for a while now with mostly PLA and some PETG. I've had no problems. I do find you need to keep it clean between prints, but that's nothing new. I didn't use the supplied magnetic base as I already have bed magnets.I take off 1 star because the plate wasn't completely flat, it has a slight warp (!) But the bed magnets really pull it flat so it works.
S**S
Didn't Fit 300mm x 300mm
The whole process of getting it here and installing it was great. But it didn't actually fit the bed that it describes that it can fit. I tried centering it, but it caused all kinds of level issues and even caught the nozzle. I decided to left bottom justify it and there is a 3/4 in top gap and a 3/8 right gap.I guess technically it "fits" on the bed, but so would a 100mm x 100mm. But this plate should actually cover the whole bed. This product is now useless to me and almost cost me a replacement nozzle.
R**A
Poor quality control
Poor quality control. I found a few areas with debris under the bed coating which caused bubbles and an uneven bed surface. The spring steel was warped and had to be adjusted with a heat gun and press. Adhesion was terrible so I lightly sanded the surface with 220 grit and even lighter with 400 grit. This seamed to fix the adhesion issue. If your willing to modify, it will work, but definitely not valued correctly.
A**R
Poor quality control and cheap materials
I would avoid this PEI spring steel sheet. First, the magnet seems fairly week. I think the spring steal will pull up off the magnet on a large ABS print. Worst of all, it came with a significant bubble in the PEI sheet, rendering a section of the bed useless. Also, it is not a plain sheet like shown, it has a grid and they put a Fystec logo all over it, which really looks bad. Overall, it appears cheap, not as described, and has poor quality control. I do not recommend this at all.
N**O
Worked well for me, no bubbles
Had it for a few weeks now, and no complaints. Works well, and didn't see any bubbles other users have complained about. I guess I got lucky.
Trustpilot
1 month ago
3 weeks ago
