Honing Compound PA70 for Use with Tormek Sharpening Grinders T-7, T-4, and T-3, and also other leather strops. Creates Razor Sharp Edges on Knives and Tools. | Stropping compound for knives and tools, 3 micron abrasive, 70 g paste, 6000-8000 grit

I can put a shaving sharp edge on my knives, but I'm always looking for a better/easier way to sharpen. Not sure what I was expecting with this honing compound... I guess I just felt that my strop wasn't quite burnishing the edge like I thought it should. Last night I had 10lb of beef to slice up very, very thinly for making jerky (that's a LOT of slices!). The meat wasn't quite fully thawed. Anyway, I pulled my Shun Kanso chef's knife (AUS8 steel @ 61Rc) from the drawer and it already had a fine, stropped edge on it. Testing the edge by gently attempting to slide it down the hair on the back of my head, it was nicely catching the hair. I'd call that edge about 95% of what I'm generally capable of achieving. But because I had just received this compound, I wanted to see if, or how much, I could improve it. My strop is a barbers strop - it's a 3" wide strip of thick leather about 30" long. It's well used. First I used a butter knife with a slight serration to kinda scrape the napped side of my strop, and tease up the fibers. Then I gave it a good spray with WD40, then applied 9 little dots of the honing compound. I spent about 2 minutes stropping the chef's knife in the usual way - a few strokes on one side, then a few strokes on the other. I probably made 20 strokes per side, total. What I ended up with is the most ridiculously sharp edge I've ever created in my life, and every bit the equal to the very best Zero Tolerance, Shun or Benchmade factory edge I've ever experienced. I mean, just scalpel sharp. Doing the "hair test", it instantly bites into the hair - and actually shaved a few even though I was being extremely gentle about it. Compared to what I'm generally able to achieve, I'd say this edge was probably 125-150%. Just incredibly sharp. So I went to work thinly slicing my slightly frozen beef. It was cutting amazingly. I made it about 1/2 way through the 10lb and even though it was cutting great, I tested the edge. It wasn't *quite* as sharp as when I began cutting, but was still very, very sharp. So I finished the job. I probably made 1000 or more cuts in total. When finished, the edge was still sharp enough to cleanly cut a piece of paper, but was ready for a touchup. I gave the edge a few licks on the strop and retested - surgically sharp again. Shaving a few hairs on my arm - it's as if the hair just jumps off my arm in fear of the edge even coming close to them! I've very, very impressed with the edge I can get with this compound. It's far better than any other edge I've ever created. I'm not "gods gift" to sharpening, and I'm not saying I'm the best - but I don't suck and this stuff has really upped my game.

I actually bought a use sharpener which was not a Tormek but had many Tormek accessories. This Tormek honing paste is good stuff. Easy to get a razor sharp edge.

Technically this is a buffing, polishing or strop compound. It will keep the fine strop finish on your blade like no other product short of home made 12,000 grit diamond dust paste...nothing beats that on a slightly damp strop, rough side 8,000 grit then smooth side 12,000 grit...but I digress. I've been using this as a strop compound an it lasts virtually forever unless you just sharpen blades all day in which case the strop leather disintegrates before the paste is completely used up. On veg tan hide 12-14 oz. I dampened the leather very slightly then rubbed a small dab along the surface areas that I know I will use on the rough side. I then embedded 12,000 grit diamond dust in the very slightly oiled smooth side. Such a strop, reapplying the paste about every 15,000 uses should last for years. Note: I'm Leary of using this on any buffing wheel that is not regulated to 1200 rpm or even a little slower as the wheel dries out and begins to shed the paste rapidly at standard 3200 rpm buffer wheel speeds. But I digress.. I tend to re-polish my blade on the strop after every 4-6" cut in my leather cutting. A sharp blade cuts smoothly! So I strop my blade at least 700-1000 times per day. Doing this with this paste means only needing to fully sharpen and restore blade angle ever few months. This paste is a pleasure to use...though I'm not sure if it would actually be useful in 'honing'.

More of a fine grit stropping compound for a final strop. Lots of compound for the price. Works best with a stropping wheel.

I don't have a Tormek but I have found this to be very useful on my leather strops.

I don’t even have a Tormek sharpener but I got some of this in an auction lot and fell in love. I’ve been buying these from Amazon since my original tube ran out. I use on a leather wheel on a worksharp but mostly on a plain leather strop. It’s a good balanced grit between aggressiveness/ speed in my opinion. I’ve only ever used a few other brands but this one is the sweet spot for me. Works great on my WW tools.

Over the years I’ve tried just about every type of stropping compound of just about every micron size on just about every type of strop material. This stuff (on leather) really surprised me. Cuts and polishes very fast and leaves a razors edge even on high HRC steels. Very pleased!

works great on a strop, would buy again.

This stuff is fantastic and works really good. I was using the hard blocks of honing compound but this stuff put a really, really razor sharp edge on my knives with a nice mirror finnish for a low friction cutting ability. They also sent it next day delivery so that was also great but remember when using this honing compound to use it sparingly as a little goes a long way. If your using a leather strop then use a little WD 40 on your strop and then put this stuff on and again sparingly. I use a Work Sharp Ken Onion Edition with a leather strop on the machine but do not use oil on the strop as it will just sit there and spin on the spindle and not go anywhere as the oil prevents traction. This is a really really effective honing compound and I recommend this 100% but what would be amazing is if this company who sells this could sell different grit sizes so you could use this on a buffing wheel to polish metal. Please don't buy honing block compounds buy this and I'm telling you, you won't buy disappointed !!!

Très bien ,comme décrit. Bon rapport qualité prix

Non ho un sistema Tomek ma volevo testare questa pasta. Peccato non sapere che grid ha. Comunque lo usata per riaffilare delle forbici da cucina (5 paia) ed il filo, al termine del trattamento con una stroppa artigianale, era a lucido (e passando su un dito con delicatezza me lo ha inciso, tipo coltello.

Produit de très belle qualité pour les ciseaux à bois ou les couteaux. On obtient une coupe très satisfaisante.

Works great on my leather strops. Better than the hard bars