SPPC For 2009-2018 Dodge Ram Smoke Black Switchback Projector Headlights Replacement Headlamps w/LED DRL

This is for the V2 versions (https://www.amazon.com/gp/product/B07R38JWN8, which give you the DRL on top AND bottom, as well as sequential blinker, and other minor improvements)I've had these since May 3rd 2019, and installed them Fri the 10th.These come with halogen (orange) H7 bulbs for hi/low, I put the following LED lights in the projectors (You WILL need to adjust the bulb rotating base AND you will need to adjust the projector correctly from 30ft).Katana H7 (https://www.amazon.com/gp/product/B07FFS4JZJ) for lowsNineo H7 (https://www.amazon.com/gp/product/B01MFABBZW) for highsNote the "Fat" notch. This is important for projectors as they mimic the output of a halogen bulb. 4 sided LEDs, and other types will not look good, or will scatter light everywhere. There is a single LED (Morimoto 2stroke 2.0) that was built for projectors but i'm cheap and would rather have both bulbs for the price of a single set). Also recommended bulbs are Supernova V4's.Install was simple, plug and play. You do not need any additional wiring unless your truck does not have DRL's (I'd recommend plugging in first). If you have not adjusted your headlights to be HID with AlfaOBD, you will need an anti-flicker harness for the low beams. If you reach out to the seller and ask for support, they'll help you out!I did put the LED driver, and the flicker harness inside the housing (Everything is sealed and dust caps on). I did notice that the plastic housing was warm after running the lights for a few hours, but this was because I had double stacked the LED drivers. Will update this more after a couple of months).The v2 "Projector" harness is available for these lights (contact the seller). This harness is required if your truck came pre-installed with projector headlamps. If it has quad/dual or single headlights, no harness is needed and is PLUG AND PLAY!Overall, these headlights look fantastic and have great light output (even with Halogen bulbs). They look absolutely amazing even for the cheaper quality plastic housing. Adjusting the projector is easy, you need a long #2 phillips or flat head, and you can adjust through the fender normally (See video)PROS:Good build quality.Amazing look.Dual projectors with great output with a good bulb.Dual DRL, and sequential blinker.Simple install.Fantastic support (They called me to discuss issues with my ram and flickering).Has lots of room for any drivers/flicker harnesses to be stuffed in. I DO wish the H7 plug was a little longer to move around and such.CONS:Thin plastic housing (Compared to OEM). A thicker housing would be nice.Better job on sealant around the headlight (While my lights looks well sealed, it did look like there were gaps and the rubber sealant for the headlight lens and plastic housing didn't fully adhere together. Some spots looked almost bare and empty. A quick bead of clear silicone around the entire front housing/lense solved any of my worries that the headlights would leak and is extremely simple to remove later on.Extremely tight mounting for the H7 bulb. I had to bend my metal tab for holding the bulb in slightly to accommodate me removing and replacing the bulb. This either means the projector was not set directly centered or that the plastic molding that holds the projector has extremely tight tolerances. Easy fix but be aware you may need to bend the springs a bit to make it easier to remove and replace bulbs.Extra cable for "plug and play" (My headlights came with this extra pigtail. When using this I was not able to use my factory connectors "Lock" latch. I just removed the extra wires and it worked perfectly.Extra "DRL" wire (red wire) was sealed poorly. A shot of silicon and my troubles were put at rest.You will need to purchase the turn signal socket (68032802AA Mopar part #), as these do not come with them.Overall, I would buy these. They mimic the 1600+$ XB's and they look just as good! Worth every penny for the V2 headlights as it provides the much needed "visual" upgrade to your ram!

It seems to be over all a good product, it came packaged very well. The over all housing is thicker then the OEM headlight, so when you go to install it you have to work it alittle bit to get it in. After installed it looks great. I'm just worried if for when I ever need to change a light bulb again. The beam adjustment was a little difficult to work with. I had to use a scribe to turn the adjustment knob.

There are gaps between the lenses and the housing. They will leak or at the very least get moisture in them. I definitely need to put a bead of silicone. I would send them back if I didn't need a headlight Right NOW! I should have listened to the reviews.

Sincerely I am waiting for a time to responsibly comment with this product, it has been a few weeks and is beginning to enter condensation within the focus, although it is very beautiful, they have to make an effort to seal it well professional as with shipping and the price, cost $ 600.

One of the headlamps came in damaged inside. Im so disappointed

Very nice product

Great product