14 inch x 1 inch x .095 inch Urethane Band Saw Tire 2 Pack for Jet: JWBS-14DXPRO JWBS-14CS JWBS14OS Grizzly: G0457 G0555 G0555P G0555X G0580 T21005 G1019 G1019Z Made in the USA

After installation i think the saw runs smooth.

I have a very old Jet that is from back in the 1980s, before they stepped up their game. It has always been possible to get it to cut, but not with precision and not without having to keep making frustratingly frequent adjustments for wandering blade syndrome. After reading the reviews for these tires I expected a moderate performance upgrade but expected that blade adjustments would still be required. It turns out that the blade tracks consistently well now adjustments are rarely required. In short, it made a much bigger difference than I expected.It is difficult to install. But with a couple of levers and some muscle it slipped on. The second one was easier.

Previous band saw tire went bad, purchased this and was able to install it fairly quickly. It was a little difficult to install as it is sized a little small on purpose. Zip tying while going around the wheel made it very easy to put on. Also comes with 2 for future replacements!

Placed on the bandsaw for the purpose it was intended to do.

Easy to install. No boiling needed, just get the tire warm with hot water from the tap.I removed the wheel and mounted it flat on my workbench using a screw and a washer. This held it firm but allowed it to turn as needed. I slipped the tire over the wheel as far as it would go and then placed two small spring clamps to hold that in place, spacing one at each side. I then used a 1/2" dowel about a foot long, slid it under the tire and working my way around slowly, but pulling hard, the tire slid into place. After carefully removing the dowel I used it to press the tire down into the recess. At first it looked like the tire was too wide and would require trimming, but that wasn't necessary in my case. It nestled into the recess and butted up to the rim at each side perfectly, I just went slowly. I mounted the wheel and spun it to check for high spots and used the dowel to press those down.After reassembly it runs smooth and true.

I like these so far. I was worried because the material didn't feel or look the same as my last pair of urethane tires. I warmed them in water like the videos on You Tube suggests, (which in hindsight the directions said you don't have to) they installed very easily. I thought they might slip because they seemed a little loose but they are working fine so far. I only gave 4 stars for longevity since I haven't used them very long yet.

Some reviews noted a need to trim for the Jet or that the tire didn't fit in the channel. If you just hold the tire to the channel, it is a hair wider and you might be concerned. However once stretched around the whole wheel, that extra width is gone and it fits just fine. You might need to pinch down the last few inches by hand but the stretch makes the belt narrower (as it should) and the result is a perfect fit.Definitely pull the wheels from the saw to install the new tires. That lets you clamp the wheel to the bench and use spring clamps to hold things in place while you work the screwdrivers or tire irons to stretch it over. I let mine sit in the sun for about 30 minutes to relax them and they went on without any undue fuss.It's definitely quieter than the old rubber tires, but those were pretty shot on my saw. Use this as an opportunity to re-tune your bandsaw.

The tires are a really tight fit. The directions say NOT to heat the tire, and to use zip-ties to ease installation (see photo). I did that and the zip-ties made it quite easy to install. The width was a little too wide in one section to fit into the recess in my bandsaw wheel. I'm not sure if it was the wheel, or the tire, might be the wheel. At any rate, I had to trim about 1/16" off the side of one tire, which was not that easy to do neatly given the strength of the tire, but I was able to trim it.

Muy duradera y el agarre con la sierra es de lo mejor. La recomiendo

Best bands I have ever put on the bandsaw. Hard to put on but well worth the effort.

I have a 20 year old machine it has given me a great service, good to know i did not have to get a new machine asparts are still available.

Was able to fix two band saws with the pair of tires, a General International and a Delta. Installation is easier with two people, but can be done alone with the help of a few clamps. Check youtube videos for installation hints.

These are a vast improvement to the original bandsaw tires on the Laguna SUV 14" bandsaw. My original bandsaw tires had a bump. These new tires helped immensely. Less vibration, and smoother operation. Highly recommended. Only problem, a little hard to put on.